Note: This installation manual assumes the door is already prepped with a 2 1/8" boring hole and latch hole.

Please note that your lock is shipped with a default user code of 1234 and default programming code of 123456. These should be deleted/changed immediately after installation for security purposes (instructions provided at the end of this installation manual).

1. Latch Installation

A. Latch Backset

The BACKSET is the distance between the center of the boring hole to the edge of the door. Set the latch backset to match your door by pulling the cam to either side.

Image A shows the latch when set to a backset of 2-3/8" (60mm) and image B shows a the latch when positioned for a 2-3/4" backset.

B. Install Latch

Insert the latch and tighten with 2 screws provided.


C. Install Strike Plate

Insert the strike and secure with screws.


2. Install Keypad Assembly

Before placing the front keypad assembly onto the outside of the door, check the following:

A. Ensure that the tailpiece is in the vertical position.

B. Pass the power cable over the latch to the interior side of the door.

Place the keypad assembly on the front of the door. Make sure to position the handle so that is facing away from the edge of the door.


3. Install Inside Mounting Plate

The inside mounting plate will secure the keypad assembly to the door. On the inside of the door, hold up the mounting plate and pass the power cable through the wire hole.


Secure the mounting plate with the largest screws provided.


4. Install Interior Lock

A. Secure the interior handle. Position the lever so that the handle faces away from the edge of the door towards the hinges.

Slide the handle onto the lock assembly and push down until it clicks into place. If you accidentally install the handle the wrong direction, instructions for changing handing are at the end of these instructions.


B. Connect the front to back power cable.


C. Place interior lock on door. Remove battery cover and ensure that the thumb turn is in the horizontal position. Then place the lock onto the door.


D. Secure interior lock with 3 screws.



5. Install Batteries

Insert 4 AA Alkaline or Lithium batteries into the battery compartment, then replace battery cover and slide the battery cover back onto the lock.

IMPORTANT: Do not use Rechargeable batteries. Rechargeable batteries can lead to inconsistent behavior on the lock.



6. High Five - Install Complete!


7. Locking and Unlocking

A. Locking

To lock your door, either turn the thumb turn on the interior handle to the vertical position. You can also lock from the keypad side of the door by pressing the LockState button twice.

B. Unlocking

Your lock has a default code of 1234. To unlock your door, enter 1234 and then press the LockState button.

All pin codes must be followed by the LockState button to unlock the door.

8. Connect to WiFi

You can now connect your lock to your WiFi router.

Click here for instructions on connecting your lock to WiFi.

9. Delete/Change Defaults

Your lock is shipped with the following factory default settings. The default pin of 1234 should be deleted after installation and the default programming code of 123456 should be changed immediately after installation.

  • Keypad Programming Code: 123456
  • User Code: 1234
  • Auto-Lock Mode: Enabled
  • Auto-lock Delay Duration: 5 seconds
  • Keypad Sound: Enabled
  • Heartbeat Interval: 1 hour
To delete the default user code:

This can be deleted from the web application under the lock settings, or from the keypad by entering:

123456 # 120 # 1234
To change default keypad programming code:

This can be deleted from the web application under the lock settings, or from the keypad by entering:

123456 # 100 # New 4-10 digit code

Changing Lever Handing

Be sure that the lever is unlocked before changing handing.
Interior Handle

Insert the provided pin wrench into the small hole on the neck of the lever and apply pressure to depress the catch pin.

Pull the handle away from the lock body off the the lock assembly. The handle can then be reversed and snapped back onto the lock.

Exterior Handle

Insert the key and turn to the unlocked position. Insert the provided pin wrench into the small hole on the neck of the lever and apply pressure to depress the catch pin.

Pull the handle away from the lock body off of the lock assembly.

The handle can then be reversed and snapped back onto the lock.